The Buyers Products LED Light Strip # 33756296144 is rated for 12 volts. It is capable of working from approximately 10-14.6 volts as that is the general range 12 volt batteries are going to be good for. view full answer...
The Optronics LED Light Strip Connector - Snap On # A90P1B has the following dimensions:
5/8" tall
13/16" length
9/16" width.
3/8" width of opening for connecting strips.
These connectors allow you to connect multiple strands of the LED strip lights like the Optronics Flexible LED Light Strip - Weatherproof - White - 17' Long # UCL90CB. view full answer...
The Optrionics Flexible LED Light Strip # UCL90CB you were looking at will have right at 171 lumens per foot of the light strip.
I included a video review of the # UCL90CB for you to take a look at. view full answer...
I reached out to ARB to verify the amount of power the LED Light Strip for ARB Awnings # ARB32ZR draws. Unfortunately they were not able to give me any power draw figures on this but we can compare it to the Buyers Products LED Light Strip # 3375626090 as it is very similar with a lumen output of 1,180 compared to the 1,200 of the ARB light strip. The Buyers pulls up to 1.3amps of 12 volt power or 15.6 watts which is going to likely be very close to the ARB lights since the strips are very... view full answer...
I was able to go out to the warehouse and measure the Bully Fire Strip LED Light # BLS-1103.
The thickness of the LED and bracket is .179 of an inch or 11/64. The overall height of the LED and bracket is .786 of an inch or 25/32 and the height of just the LED portion is .476 of an inch or 15/32.
The light strip should not be removed from the housing of which it is incased, this will damage the function of the light and void the warranty. If the above measurements do not suit your Escape... view full answer...
I spoke with Optronics and they informed me that if you used the full reel of the Optronics Flexible LED Light Strip - Weatherproof - White - 17 Long Item # UCL90CB the amperage draw would be 2.7 amps. view full answer...
The effective lumens rating for the Optronics LED Thinline Interior Lights, # ILL71CB, is 342 lumens. It is difficult to compare the lumens output of this LED light strip to a 2 tube fluorescent light without knowing the length and wattage of the fluorescent bulbs.
After doing some research, it seems that many 16 inch fluorescent bulbs are 16-watts and these bulbs have a lumens output of 1000. With this information, we could say that a 2 bulb fluorescent light that has two 16 inch, 16-watt... view full answer...
Yes, the Bully Fire Strip LED Light for 48" or 60" Tailgates # BLS-1101 that you referenced comes with two 30 inch strips that can be cut to length if needed.
I attached a review video for you to check out as well. view full answer...
The Replacement Blue LED Light Package for Thomas Payne Seismic # LC354490 have 22" long light strips. These strips are meant to replace the lights on one side of the theater seating setup, so in order to replace the lights on an entire sofa, you would need 2 of these. view full answer...
I went out to our warehouse to take a look at the Replacement LED Light Strip # LC423331 that you referenced. The light strip itself is extremely thin so it's going to pretty much fit inside any housing that's designed for this purpose. I also grabbed the complete light kit, part # LC674283, that this is a replacement strip for and found that the housing opening was just about 1/16 of an inch.
So as long as your existing housing is at least this size the replacement strip will work perfectly.... view full answer...
You're in luck because the width is exactly 3/8" of the Diamond light strip, which is the following part number:
- Smart LED Light Strip w/ App and Wireless IR Remote Control # DIA66QR
The # DIA66QR is also a total of 16' long, but you can cut it every 2" to make it fit wherever you need, and you can power it via standard 110 volt plug, or by wiring it to a 12 volt source. view full answer...
The width of the Optronics Flexible LED Light Strip # UCL90CB is about 3/8". I have attached a review video where we take this measurement for you to check out.
To help remove the 3M adhesive I recommend using some heat like a hair dryer or something similar. You may need to use a tool to scrap the adhesive off as well. I'd try using something that is plastic or rubber to help avoid scratching anything. view full answer...
I went out in our warehouse and grabbed a Bright Ideas 18" Surface Mount LED Strip Light # 277-000169 to measure the holes and found they are 3/16 of an inch and are 1 inch apart measured on center.
The mounting holes do have metal sleeves ran through them, but I still wouldn't recommend using rivets as a way to secure the strip. Bolts and nut would be ideal. view full answer...
The Access LED Lighting System for Truck Beds # A80312 measure 18-inches long x 1/4-inch wide. This lighting system has 30-LEDs and requires 3 AA batteries for operation. view full answer...
Each little connection wire between the lights on the Alpena Trailblaze Tailgate LED Lights # ALP77229 is approximately 4" in length and the wire with the 4-pole connector is approximately 41-1/2" in length. view full answer...